Cooper Tools Quackenbush 158QGDAV Manual do Utilizador

For additional product information visit our website at http://www.apextoolgroup.comService ManualPL92-5000EN05/14/2012158QRA & 158/15QRA SeriesAd

Page 10PL92-5000EN05/14/2012“B”642011PT Motor Module18Quackenbush®Motor Module17161514121311108576943421

Page 11PL92-5000EN05/14/2012ENDescription-- 641660 1 Motor Housing Assembly (includes Ref. 1 - 5)1 615391 1 Exhaust Deflector2 615467 1 2 Wire Screen3

Page 12PL92-5000EN05/14/2012“C”621251 Gearing Assembly9Quackenbush®Gearing Assembly677854321

Page 13PL92-5000EN05/14/2012ENDescription1 619421 1 Lock Nut2 613285 1 Internal Gear3 864471 1 2 Ball Bearing4 617370 1 Planet Cage Washer5 612050 1 P

Page 14PL92-5000EN05/14/2012“D”19Quackenbush®158 Right Angle Drill Head - HousingHand Tighten: RH Thread4 in. lbs.17*19872423161828252320242627324Nylo

Page 15PL92-5000EN05/14/2012ENDescription-- Table "D" 1 Drill Head Assembly1 624622 1 Housing2 624615 2 4 Clutch Plunger3 624916 2 6 Clutch

Page 16PL92-5000EN05/14/2012“E”8Quackenbush®158 Right Angle Drill Head - GearingHand Tighten: RH Thread* Note: Not included in Drill Head AssemblyWARN

Page 17PL92-5000EN05/14/2012ENDescription-- Table "E" 1 Drill Head Assembly1 Illustration "D" 1 Housing2 624617 2 4 Screw (6-32 UN

Page 18PL92-5000EN05/14/2012Blank PageQuackenbush®158 Right Angle Drill Head - Gearing

Page 19PL92-5000EN05/14/2012Table "E"Ref. Description # Part Number Feed Rate-- Drill Head Assembly 1 621915 .001-- Drill Head Assembly 1 62

Page 2PL92-5000EN05/14/2012XXX Q R A - XXX - XX - 9.50 X X - X XXX - XXXTool Series158 = Positive Feed158/15 = Positive FeedBrandQ = QuackenbushTool S

Page 20PL92-5000EN05/14/2012“F”12Quackenbush®158/15 Right Angle Drill Head - Housing22232119Hand Tighten: RH Thread20131810 in. lbs.456Nylok1416151732

Page 21PL92-5000EN05/14/2012ENDescription-- Table "F" 1 Drill Head Assembly1 622986 1 Housing2 613828 1 Nameplate3 834228 2 4 Drive Screw4 6

Page 22PL92-5000EN05/14/2012“G”Quackenbush®158/15 Right Angle Drill Head - GearingWARNING: Spindle wrench (45) is used to hold the spindle wh

Page 23PL92-5000EN05/14/2012ENDescription-- Table "G" 1 Drill Head Assembly1 Illustration "F" 1 Housing2 622985 1 Gear Stop3 62298

Page 24PL92-5000EN05/14/2012Table "G"Ref. Description # Part Number Feed Rate-- Drill Head Assembly 1 631778 .001-- Drill Head Assembly 1 63

Sales & Service CentersNote: All locations may not service all products. Please contact the nearest Sales & Service Center for the appropriate

Page 3PL92-5000EN05/14/2012Language Version:This Parts Manual is the “Original Instructions” intended for all persons who will use or re

Page 4PL92-5000EN05/14/2012The spindle on right angle positive feed drills retracts at a much faster rate than it feeds. Care must be taken to avoid e

Page 5PL92-5000EN05/14/2012Warning Labels:The warning labels on these tools are essential parts of the product and are not to be removed. Chec

Page 6PL92-5000EN05/14/2012158 Drill Head:Refer to Illustrations “D” & “E”.158 Drill Head Disassembly:Remove the stop body assembly (4 screw

Page 7PL92-5000EN05/14/2012Remove the cover (2 screws) from the drill head housing. The gearing components can now be disassembled as shown in Illustr

Page 8PL92-5000EN05/14/2012Page 8“A”Hand Tighten: RH ThreadRef.Quackenbush®Handle & Sensor Assemblies201916181516141112136867103917123452 in. lbs.

PL92-5000EN05/14/2012Page 9ENDescription-- 642014PT 1 Handle Assembly (includes Ref. 1 - 15)1 642015PT 1 Throttle Handle (includes Ref. 6-8)2 613254 1